A lot of homeowners have no idea what their water pipes are made of, and there is no reason they should. It usually only comes up when the shower pressure has been fading for years or a pipe finally starts leaking. Finding out what you have takes a flashlight, a fridge magnet and a short walk around the house, and it tells you a great deal about what is going on inside your walls. A flashlight, a refrigerator magnet and ten minutes around the water heater and the hose bibs will usually settle it.
Where your pipes show themselves
Most of a house’s supply piping is hidden in the walls, the attic or under the slab, but there are a few places where it comes out into the open, and those are where you check. Start at the water heater. The two lines on top, cold in and hot out, are usually visible for a foot or so before they disappear into the wall or ceiling.
Next, open the cabinet under the kitchen sink and under each bathroom sink. Look past the flexible lines going up to the faucet and find the stub coming out of the wall where the shutoff valve sits. Then head outside to a hose bib and look at the pipe right where it leaves the wall, and check the main shutoff where the line comes into the house.
Check more than one place. Plenty of homes have been partly repiped over the years, so the water heater might be on copper while the line to the back bathroom is still the original. Jot down what you find at each spot, because the pattern matters as much as any single pipe.
The color test and the magnet test
Copper is easy once you have seen it. New copper is the color of a bright penny, and older copper darkens to brown and sometimes shows a green or bluish crust at the fittings. The joints are smooth and soldered, or joined with fittings that look pressed on. Copper is not magnetic.
Galvanized steel is gray, sometimes a dull silver and sometimes dark and rusty. The giveaway is the threads. Galvanized pipe screws together, so at every fitting you will see threads where the pipe goes into an elbow or a coupling. Hold a magnet to it. If it sticks, you are looking at steel.
Watch out for the valves themselves when you test. Shutoff valves and some fittings are often brass, a yellowish metal that a magnet will not grab either, so judge the pipe running into and out of the valve rather than the valve body.
If the color is hard to judge under years of paint or grime, scratch a small spot with a key or a coin. Copper shows that penny color underneath, and galvanized shows gray metal. You may also run into plastic, either rigid white or cream colored pipe or flexible tubing in red, blue or white. Those are newer materials, and finding them usually means somebody already replaced that stretch at some point.
What galvanized does on the inside
Galvanized steel pipe has a zinc coating that is there to keep it from rusting. That coating wears away over the decades, and once it is gone, the steel underneath starts corroding from the inside. Rust and mineral scale build up on the inner wall of the pipe, a little more each year, and the opening the water travels through keeps getting smaller.
That is why houses with old galvanized lines have pressure that seems to fade over time. A shower that used to be strong turns weak, and running two fixtures at once drops both of them. Sometimes the water comes out brownish after it has been sitting, especially first thing in the morning. Hard water speeds the buildup along, and the water in this part of the Inland Empire is hard. Water quality around Highland is one of the things that shapes what we recommend for a house here.
Galvanized also tends to fail at the threads, where the pipe wall is thinnest. A leak at one fitting on an old galvanized line is often the first of several.
What moving to copper involves
Replacing galvanized supply lines with copper means running new pipe from the main to each fixture, the water heater and the outside hose bibs. Copper holds up well, it does not rust shut the way galvanized does, and the inside stays smooth, so the pressure stays where it belongs.
The part that worries people is the walls. A good repipe is planned so the walls get opened only where a new line actually has to pass, using attic space and existing routes wherever the house allows it. Openings are kept small and patched afterward. Your fixtures and finishes stay where they are, and what changes is the pipe behind them.
Outside runs count too. A hose bib on the side of the house fed by old galvanized gets the same weak, rusty water the inside does, so a repipe usually includes new copper out to those spigots, sometimes laid in a shallow trench along the house wall. Our page on copper repiping for Highland homes goes into how we plan the job from the main to the last hose bib.
Mixed piping and when to replace it
If what you found is a mix, some copper and some galvanized, that is common in older houses. A section gets replaced when it leaks and the rest stays. The catch is that where galvanized meets copper directly, the two metals can corrode each other at the joint unless the connection was made with the right fitting, and that joint is a frequent spot for leaks and rust.
Finding galvanized does not mean you need to repipe tomorrow. If the pressure is fine, the water runs clear and nothing is leaking, you have time to plan. Watch for the signs the pipe is near the end: falling pressure, discolored water, a leak at a threaded fitting, or a second leak not long after the first.
When those start piling up, replacing the supply lines all at once usually beats patching one fitting at a time, because every patch disturbs the old pipe right next to it. You can read more about the work itself on our copper repiping page.
Questions about old pipe
Can I just replace the galvanized sections I can see?
You can, and for a single leak that is sometimes the right move. The trouble is that the pipe you can see is usually the same age as the pipe you cannot, and it is scaled up the same way inside. Replacing a few visible feet rarely brings the pressure back, because the narrow parts are still sitting in the walls.
Why is my water brown in the morning but clear later?
Water that sits overnight in old galvanized pipe picks up rust from the inside of the line, so the first draw comes out discolored. Once fresh water has run through, it clears up. It can also point to sediment in the water heater. Either way it is worth a look, and checking what your pipes are made of tells you which is more likely.
Does a repipe mean tearing out my walls?
No. A repipe is planned around where the new lines have to run, and most houses have attic routes that keep the openings small. Walls get opened only where a line has to pass, and they get patched afterward. We walk you through where every opening will be before anything gets cut, so nothing about it is a surprise.
If your pressure has been fading, or you found threads and a magnet that sticks, call the shop at (909) 888-8736 or tell us what you found. Say where you looked, and we can usually tell you a fair amount before we ever come out.