Somebody calls because the kitchen drain backed up again, and the first thing we ask is how it got cleared the last time. Most of the time the answer is a snake, either one from the hardware store or one a plumber ran down the line a few months back. A snake does its job. It opens the drain and the water goes down. What it does not do is clean the pipe, and that difference is most of the reason some lines around Loma Linda come back a month later while others stay clear for years.
What a cable actually does down there
A drain cable, the snake most people picture, is a coiled steel line with a cutting head on the end. It spins its way down the pipe until it reaches the clog and then chews into it. The water starts moving again and everybody is happy, for a while.
The trouble is the size of the hole it leaves. The cutting head is smaller than the pipe, so it bores a tunnel through the middle of the blockage and leaves whatever is stuck to the walls right where it was. On a kitchen line that is a ring of hardened grease. On a sewer lateral it is usually roots that came in at a joint, trimmed back but still hanging there.
Water runs through that tunnel fine at first. Then food scraps, soap and fresh grease catch on the rough edges and the opening closes up again, a little narrower every round. That is why a line that gets snaked tends to need snaking again, sometimes on a schedule you could set a calendar by. A cable is still the right tool for plenty of simple clogs, a hairball in a tub drain for one, and we carry them on every truck.
What water under pressure takes off the wall
A jetter pushes water through a hose with a nozzle on the end that sprays backward and outward at high pressure. The backward jets pull the hose up the line, and the spray hits the whole inside of the pipe on the way through. It scours the grease, scale and root hair off the pipe wall and flushes all of it downstream, where the cable would only have drilled a path through.
What you end up with is a pipe close to its full width again, with nothing rough left for the next batch of grease to grab onto. That is the reason a jetted line stays open so much longer than a snaked one. There is simply less in there for new buildup to start on.
Jetting also reaches farther and handles more in one pass. A long run from a kitchen out to the street, with grease coating every foot of it, is a slog with a cable and a pretty straightforward job with a jet. Our hydro jetting page goes into the equipment and the kinds of lines we use it on. It is still not the answer to every slow drain, and the camera is how we decide when it is.
Why the camera goes down before the jet
If a line has been cleared once and it backs up again, something physical is holding the debris, and clearing it a third time without looking is paying to repeat the same problem. So on a repeat call we run a camera in first.
The camera tells us two things. One is what the blockage really is: grease built up along the bottom, roots at a joint, a belly where the pipe has sagged and water sits, or something that got flushed and wedged. The other is whether the pipe is in shape to be jetted at all. An old line that is cracked through, badly offset at a joint or crumbling in spots is not a pipe you want to hit with high pressure water, because you can make a bad section worse.
Most lines we look at are fine to jet. When one is not, you find out on the screen, with the spot located, and we talk about repairing that section instead. You get to see what we see, and nothing gets decided on a guess. The camera rides on the truck alongside the jetter, so this usually happens on the same visit.
Wipes and grease keep coming back
When we pull debris out of a main line on a house, the two things we see most are grease and wipes. Grease goes down warm and liquid, then cools and hardens on the pipe wall a little farther along. It builds in layers, and a snake opens a path through those layers without taking them off.
Wipes are bad in their own way. The packet can say flushable all it wants, they do not come apart in the line the way toilet paper does. They snag on a rough spot or a root, collect more wipes behind them and turn into a mat. A big share of the main line stoppages we clear in this area trace back to them.
Jetting gets both out of the pipe, but it cannot keep them from going back in. A household that keeps flushing wipes or rinsing pan grease into the sink will build the same blockage again, just more slowly on a clean pipe. Wipe the pan with a paper towel before it gets washed, put wipes in the trash, and a jetted line will tend to stay clear for a long time.
What a cleanout outside has to do with it
A jetter goes into the line through a cleanout, which is a capped pipe that comes up from the sewer lateral, usually somewhere along the outside of the house. Going in from outside means the hose never travels through your bathroom or kitchen, and the jet can run the length of the main toward the street with nothing in its way.
Plenty of older houses either never had a proper cleanout or have one buried under a planter that nobody has seen in years. When that is the case we can add one. It means digging down to the lateral, cutting in a riser and joining it with shielded couplings, then bringing it up to grade with a cap you can reach. After that, every future camera run or clearing goes in through the same spot, which keeps it quick and keeps the mess outside.
If you are in Loma Linda and a drain keeps coming back, our page on hydro jetting for Loma Linda homes covers how we handle it here, from the first look with the camera to the cleanout.
Questions about jetting a drain
Is jetting overkill for a slow bathroom sink?
Usually, yes. A bathroom sink that drains slowly most often has hair and soap caught near the trap, and a small cable or simply pulling the stopper and cleaning it fixes that. Jetting earns its keep on the longer lines that carry grease and on the main out to the street, where buildup coats the whole pipe instead of sitting in one spot.
How do I find out if my house has a cleanout?
Walk the outside of the house near where the bathrooms are and look for a short capped pipe, often white plastic or older cast iron, sticking up a few inches from the ground. Plants or gravel can hide it. If you cannot find one, we can locate the lateral and tell you whether adding a cleanout makes sense for your house.
Why can’t a jetter fix a sagging section of pipe?
Because the trouble is the shape of the pipe, and a jet only cleans what is inside it. A sagged stretch, a belly, holds standing water, and solids settle in it every time a drain runs. Jetting empties it out and the low spot starts filling again that same day. The lasting fix is to dig up that section and relay it at the right slope, and the camera shows us where it sits.
If a drain at your place has been cleared more than once and it is slowing down again, call the shop at (909) 888-8736 or tell us what it is doing. We will start with a look down the line and go from there.